Wizdeo Analytics

Spare parts #9 - Making A Rectangular Bluing Tray

Ajouté le jeu. 3 déc. 2015 Vie pratique et style Rectangular HD

Making A Rectangular Bluing Tray, by Clickspring

It can be a bit hit and miss getting a consistent, uniform blue on long slender parts like clock hands. So I made a third component for the bluing tray set, to do the job right. Using a scrap piece of brass left over from the frames of the current clock build, I used a shop made D bit to mill some grooves so that it could be folded into the shape of a box.

The other videos that this video is related to are:

"Spare Parts #8 - Making A D Bit Single Flute Milling Cutter": https://youtu.be/jlNxvnOxMCE

"Home Machine Shop Tool Making - Making A Versatile Bluing Tray": https://youtu.be/8h1Uf9bkc3E

If you would like to help support the creation of these videos, then head on over to the Clickspring Patreon page: https://www.patreon.com/clickspring

You can also help me make these videos by purchasing via the following Amazon Affiliate links:

Cameras used in this video:
Panasonic GH5 - https://amzn.to/2rEzhh2
Panasonic X920 - https://amzn.to/2wzxxdT

Tools & Shop Products:
"Solidworks 2013 Bible": http://amzn.to/2FObS1D
"Milling: A Complete Course (Workshop Practice Series)" - https://amzn.to/2K2QZ97
"Hardening, Tempering and Heat Treatment (Workshop Practice Series)" - https://amzn.to/2KbZo6l
Kaowool 24" X 12" X 1" 2400 F Ceramic Fiber Insulation: http://amzn.to/2pfsM3d
Blue Matador Abrasive Paper - https://amzn.to/2IAFiBT
Dormer A190202 Jobber Drill Set, 1.0 mm - 6.0 mm x 0.1 mm Size: https://amzn.to/2DR5fdb
Dormer A190203 Jobber Drill Set, 6.0 mm - 10.0 mm x 0.1 mm Size: https://amzn.to/2ITfeTa
YG1 NC Spotting Drill 8% Cobalt HSS 1/8 to 1/2" 120 Degree 5 Pc Set CNC Machine: https://amzn.to/2G7ylv6
Dykem 80300 Steel Blue Layout Fluid, Brush-in-Cap (4oz): http://amzn.to/2HGPaJJ

Abbreviated Transcript:

00:03 This bluing tray set that I made in a previous video has been working well for bluing screws and other small parts.
00:20 Some of the blued parts coming up in the clock build in the near future, are quite long and thin, so a longer tray will be required when I blue them.
00:29 However the box shape would present a bit of a challenge at the soldering stage if it was made of separate parts, so I'm making it as one piece that can then be folded into shape. Now there a quite a few ways to tackle this job, but I thought I'd show you a mill equivalent of the super glue arbor you've seen me use so often on the lathe
00:54 I'm using this block of aluminium to hold the workpiece, and the first thing I'm going to do is give it a light resurface with this flycutter. The flycutter is shop made, and has quite a lot of mass in the disc, and generally gives me a smooth cut.
01:30 Acetone cleans off the surface, and a light coating of glue is enough to hold the part. Once the work is in position, pressure from the spindle holds it in place as the glue cures.
01:44 I can now machine all of the exposed surfaces in the one operation, starting with the perimeter. I've made this D Bit cutter specifically to cut the v grooves. Click the link if you'd like to see a video showing how this was made.
02:18 The cutter has an included angle of 92 degrees, which is going to help when it comes to bending everything to shape later. I also shifted the cutter across to take a final skim cut on the sides of each groove, to create a little more space for the solder to fill.
02:39 And as always with superglue, a gentle heat breaks the bond. The little corner pieces need to be removed before I can fold the box to shape, so I used a jewellers saw takes care of those, and then I tidied up the saw cut on the belt sander.
03:18 I set about forming it into the shape of a box, with some flux, silver solder and tying wire. Now that the brass is annealed, it bends easily without cracking, leaving a small gap for the solder.
04:30 The brass holds the box shape well when its cool, but it'll flex and sag quite a lot when under heat, so I used some soft tying wire to bind it all together for the soldering operation. A little more flux, and then a good measure of silver solder was placed into position, enough to form a decent fillet when it flows.
05:41 The corners came out quite close and square, but I decided it would be better to round
them off, to match the curve of the bent edges. Then I took the part back to the mill, to form the thread for the handle.
06:14 Now the tray should lean comfortably on the handle when its sitting on the bench, so the feet need to be positioned slightly forward of the center of gravity to achieve this. Using a scrap rod, I decided on a pivot distance that gave a good result, and then formed the holes and threads for the feet.

References:

"The Model Engineers Workshop Manual" pg 94
George H Thomas

The many forum posts on the subject of D Bits
by John "Bogstandard" Moore

Making A Rectangular Bluing Tray, by Clickspring.